模具述语

一、入水：gate

进入位：　gate location

水口形式：gate type

大水口：edge gate

细水口： pin-point gate

水口大小：gate size

转水口：　switching runner/gate

唧嘴口径：　sprue diameter

二、流道: runner

热流道：　hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道：round(full/half runner

流道电脑分析：mold flow analysis

流道平衡:runner balance

热嘴：　hot sprue

热流道板：hot manifold

发热管：cartridge heater

探针: thermocouples

插头：　connector plug

插座： connector socket

密封/封料： seal

三、运水：water line

喉塞：line lpug

喉管：tube

塑胶管：plastic tube

快速接头：jiffy quick connector plug/socker

四、模具零件：　mold components

三板模：3-plate mold

二板模：2-plate mold

边钉/导边：leader pin/guide pin

边司/导套：bushing/guide bushing

中托司：shoulder guide bushing

中托边L：guide pin

顶针板：ejector retainner plate

托板：　support plate

螺丝： screw

管钉：dowel pin

开模槽：ply bar scot

内模管位：core/cavity inter-lock

顶针：　ejector pin

司筒：ejector sleeve

司筒针：ejector pin

推板：stripper plate

缩呵：movable core,return core core puller

扣机(尼龙拉勾)：nylon latch lock

斜顶：lifter

模胚(架)： mold base

上内模：cavity insert

下内模：core insert

行位(滑块)： slide

镶件：insert

压座/斜鸡：wedge

耐磨板/油板：wedge wear plate

压条：plate

撑头: support pillar

唧嘴： sprue bushing

挡板：stop plate

定位圈：locating ring

锁扣：latch

扣鸡：parting lock set

推杆：push bar

栓打螺丝：S.H.S.B

顶板：eracuretun

活动臂：lever arm

分流锥：spure sperader

水口司:bush

垃圾钉：stop pin

隔片：buffle

弹弓柱：spring rod

弹弓:die spring

中托司：ejector guide bush

中托边：ejector guide pin

镶针：pin

销子：dowel pin

波子弹弓：ball catch

喉塞: pipe plug

锁模块：lock plate

斜顶：angle from pin

斜顶杆：angle ejector rod

尼龙拉勾：parting locks

活动臂：lever arm

复位键、提前回杆：early return bar

气阀：valves

斜导边：angle pin

术语：terms

承压平面平衡：parting surface support balance

模排气：parting line venting

回针碰料位：return pin and cavity interference

模总高超出啤机规格：mold base shut hight

顶针碰运水：water line interferes withejector pin

料位出上/下模：part from cavith (core) side

模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.

不准用镶件： Do not use (core/cavity) insert

用铍铜做镶件： use beryllium copper insert

初步(正式)模图设计：preliinary (final) mold design

反呵：reverse core

弹弓压缩量：spring compressed length

稳定性好：good stability,stable

强度不够：insufficient rigidity

均匀冷却：even cooling

扣模：sticking

热膨胀：thero expansion

公差：tolorance

铜公(电极)：copper electrode

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Surface Appearance 外观

Glossiness/gloss finish 光洁度

Matt finish/matt surface 毛面

Glass fiber rich surface/glass emergence on the surface 玻纤外露

Blooming/surface blooming 表面析出

White patches on surface 表面白斑

Silver marks/silver streak 银纹

Splay mark 水纹

Flow mark 流纹

Weld line 溶结纹

Brittle/brittleness 脆

Bubbles/trapped gas 气泡

Void 孔

Burn marks 烧伤

FR failed 阻燃不合格

Flame rating V-2 阻燃V-2

Poor dispersion 分散不好

FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块

Pellet porous 粒子不密/蜜蜂窝

Low impact/tensile etc 物理性能低

High flow/filler content etc 流动性/填充…过高

Longs/fines/doubles 长粒/碎屑/连粒

Poor cut 粒形不好

Bristle/voids 表面有小气泡/孔

Glass bundles 玻纤结团

Product was rejected due to 产品不能接受因为…

High moisture level 高水分

Warpage/warped 翘曲

Shrinkage/shrink 收缩

Sink marks 缩影

Short shot/short molding 打不满

Distortion 变形

Over dimension 尺寸过大

Under dimension 尺寸过小

Flashing 飞边

Discoloration 变色

Off color 颜色差异

Flow rate 流动率

Viscous 粘

High flow 高流动

Low flow 低流动

Sticky 粘

Mold release 脱模

Antioxidant 抗氧剂

Flame retardant agent 阻燃剂

Heat stabilizer 热稳定剂

Chopped glass fiber 短切玻纤

Roving glass fiber 粗纱/长玻纤

Glass beads 玻璃微珠

Milled fiber 碾磨纤

Molybdenum disulfide/moly/MoS2 二硫化钼

Colorant 着色剂

Pigment 颜料

Dye 染料

Accepted product specification 接受产品规格

Approved our product 认可我们的产品

Re-set spec 重新定标准

Add in extra … 添加多一点…

Reduced … content 减少…含量

Dropped/reduced … by x% 减少…含量…%

Confirmed color standard 确认颜色标准

Approved color standard 认可颜色标准

Re-confirmed color standard 重新确认颜色标准

Qualified our product 认可我们的产品

Undergoing heat aging test 在做热老化实验

Product is under testing 产品在测试当中

Received first order 接了第一个定单

Expected to finish by … 预计在…完成

Expected order is xMT 预计定单量…吨

Estimated annual/monthly consumption 预计年/月用量